[2025年09月]更新のEDGE EDGE-Expert公式認定ガイドPDF [Q39-Q53]

The post-construction stage in EDGE certification requires evidence to confirm that the efficiency measures claimed in the design stage have been implemented as specified. For window glazing, which affects energy efficiency through its U-value (thermal transmittance) and SHGC (Solar Heat Gain Coefficient), the EDGE Certification Protocol provides clear requirements: “At the post-construction stage, the Client must provide manufacturer’s data sheets for the window glazing measure, showing the make and model, U-value, and SHGC of the installed glass, to confirm that the glazing matches the specifications claimed in the self- assessment and meets the energy efficiency requirements” (EDGE Certification Protocol, Section 3.4: Post- Construction Requirements). Option C, manufacturer’s data sheets showing the make and model, U-value, and SHGC of the installed glass, directly matches this requirement, as it provides the specific technical data needed to verify compliance. Option A (design building elevations marking the window glass specifications) is relevant at the design stage, not post-construction: “Design elevations are required at the preliminary stage to show intended glazing specifications, not after construction” (EDGE Certification Protocol, Section 3.2:
Audit Requirements). Option B (bill of quantities with specifications highlighted) is insufficient on its own, as it may not provide detailed technical data: “Bills of quantities may support purchase verification, but manufacturer’s data sheets are required for technical specifications like U-value and SHGC” (EDGE Certification Protocol, Section 3.4: Post-Construction Requirements). Option D (window schedule showing major glass types) is helpful but not sufficient, as it lacks the detailed technical data: “Window schedules may indicate glass types, but they do not replace the need for manufacturer’s data sheets with U-value and SHGC at post-construction” (EDGE User Guide, Section 6.2: Documentation Requirements). The EDGE User Guide further clarifies: “For glazing measures, post-construction evidence must confirm the installed product’s performance through manufacturer’s data sheets, ensuring alignment with the design-stage claims” (EDGE User Guide, Section 4.1: Insulation Measures). Thus, manufacturer’s data sheets (Option C) are required at the post-construction stage.
Reference:EDGE Certification Protocol, Section 3.4: Post-Construction Requirements, Section 3.2: Audit Requirements; EDGE User Guide Version 2.1, Section 6.2: Documentation Requirements, Section 4.1:
Insulation Measures.

In EDGE, the Base Case is a standardized benchmark used to calculate utility cost savings, reflecting typical resource consumption for a building in its location and typology. The term “virtual energy” in EDGE refers to the energy required for heating, cooling, lighting, and other systems, modeled as if the building operates under typical conditions without efficiency measures. The EDGE User Guide explains how utility costs are calculated: “The Base Case for utility costs includes the cost of virtual energy, which represents the modeled energy consumption for the building type in the absence of efficiency measures, alongside water consumption, using localtariffs to estimate financial impacts” (EDGE User Guide, Section 2.3: Using the EDGE App). Option B, includes the cost of virtual energy, aligns with this approach, as the Base Case accounts for all modeled energy use to establish a baseline for savings. Option A (excludes the cost of virtual energy) is incorrect, as virtual energy is a core component of the Base Case: “Virtual energy in EDGE is the theoretical energy use calculated for the Base Case, including heating, cooling, and lighting, and its cost is always included in utility cost calculations” (EDGE Methodology Report Version 2.0, Section 4.4: Cost Savings Calculations). Option C (excludes the cost of virtual energy only in homes) and Option D (includes the cost of virtual energy only in homes) are also incorrect, as the treatment of virtual energy is consistent across all typologies: “The Base Case methodology, including the inclusion of virtual energy costs, applies uniformly to all building types in EDGE, whether homes, hotels, or offices, to ensure a fair comparison of savings” (EDGE User Guide, Section 2.3: Using the EDGE App). The EDGE Methodology Report further clarifies: “Utility costs in the Base Case are derived from virtual energy and water consumption, reflecting typical usage patterns for the building type and location, ensuring that savings calculations are comprehensive and include all relevant energy demands” (EDGE Methodology Report Version 2.0, Section 4.4: Cost Savings Calculations). This consistent inclusion of virtual energy costs across all typologies makes Option B the correct answer.
Reference:EDGE User Guide Version 2.1, Section 2.3: Using the EDGE App; EDGE Methodology Report Version 2.0, Section 4.4: Cost Savings Calculations.

EDGE Zero Carbon certification requires specific prerequisites and operational data to verify performance.
The EDGE Certification Protocol details the requirements: “To apply for EDGE Zero Carbon certification, a project must first achieve EDGE Advanced certification, which requires at least 40% energy savings.
Additionally, EDGE Zero Carbon certification mandates at least one year of operational data at 75% occupancy to confirm energy performance, after which carbon offsets can be purchased for the remaining energy use to achieve zero carbon status” (EDGE Certification Protocol, Section 2.3: Certification Levels). In this scenario, the building’s energy savings have increased to 60% with solar panels, qualifying it for EDGE Advanced (40% minimum). The next step is to gather one year of operational data before applying for EDGE Zero Carbon, making Option C (after achieving EDGE Advanced certification and gathering one year of operational data) correct. Option A (as soon as one year of operational data) skips the EDGE Advanced requirement: “EDGE Advanced is a prerequisite for EDGE Zero Carbon” (EDGE Certification Protocol, Section 2.3: Certification Levels). Option B (no wait time) is incorrect, as operational data is mandatory:
“Operational data is required to verify performance for Zero Carbon certification” (EDGE User Guide, Section 6.3: Advanced Certifications). Option D (at the same time as EDGE Advanced and after two years) is wrong, as only one year of data is needed: “One year of operational data at 75% occupancy is sufficient for EDGE Zero Carbon” (EDGE Certification Protocol, Section 2.3: Certification Levels). Thus, Option C is the correct timeline.
Reference:EDGE Certification Protocol, Section 2.3: Certification Levels; EDGE User Guide Version 2.1, Section 6.3: Advanced Certifications.

The EDGE software estimates water use in homes by considering elements that contribute to potable water demand, focusing on indoor and occupant-related usage. The EDGE User Guide details the elements included in water use calculations: “In EDGE, water use in homes is estimated based on occupant activities, including water for showers, faucets, toilets, laundry, and water heating, which accounts for hot water demand in these applications. These elements are modeled using standard usage assumptions for residential buildings” (EDGE User Guide, Section 5.2: Water Efficiency Measures). Option B, water heating, is explicitly included, as it represents the hot water demand for showers, faucets, and laundry, which is a significant component of residential water use. Option A (HVAC) is incorrect, as HVAC systems primarily consume energy, not water, except in specific cases like cooling towers, which are not typical in homes: “HVAC systems in homes, such as air conditioners, do not directly contribute to water use in EDGE calculations, unlike in commercial buildings with cooling towers” (EDGE Methodology Report Version 2.0, Section 4.2: Water Savings Calculations). Option C (exterior fountains) is also excluded, as EDGE focuses on indoor water use: “Exterior water use, such as for fountains or irrigation, is not typically included in EDGE’s water use estimates for homes, unless specifically modeled as an optional measure, which fountains are not” (EDGE User Guide, Section 5.3: Additional Water Efficiency Measures). Option D (solar water heaters) is a measure to reduce energy use for water heating, not an element of water use itself: “Solar water heaters reduce the energy demand for water heating but do not change the volume of water used, which is what EDGE estimates for water use in homes” (EDGE User Guide, Section 4.2: Energy Efficiency Measures). The EDGE Methodology Report further specifies: “Water use in homes is calculated based on per-capita assumptions for activities like showering, flushing, and water heating, ensuring a standardized baseline for savings calculations” (EDGE Methodology Report Version 2.0, Section 4.2: Water Savings Calculations). Thus, water heating (Option B) is the element considered in EDGE to estimate water use in homes.
Reference:EDGE User Guide Version 2.1, Section 5.2: Water Efficiency Measures, Section 5.3: Additional Water Efficiency Measures, Section 4.2: Energy Efficiency Measures; EDGE Methodology Report Version
2.0, Section 4.2: Water Savings Calculations.

The EDGE Standard defines specific project types eligible for certification levels, including EDGE Advanced, which requires at least 40% energy savings. The EDGE Certification Protocol specifies: “EDGE Advanced certification is available for new constructions that achieve a minimum of 40% energy savings compared to the base case, applicable to building typologies such as homes, hotels, offices, hospitals, retail, and schools” (EDGE Certification Protocol, Section 2.3: Certification Levels). Option A, new constructions, aligns with this scope, as EDGE focuses on new buildings across supported typologies. Option B, green lease agreements, is not a building type and is outside EDGE’s certification framework. Option C, infrastructure constructions, and Option D, parks and landscape projects, are also not covered under EDGE typologies, as confirmed by the EDGE User Guide: “EDGE certification applies to new buildings and major renovations of specific typologies, excluding infrastructure or landscape-only projects” (EDGE User Guide, Section 1.2:
Scope of EDGE Certification). Thus, only new constructions qualify for EDGE Advanced certification.
Reference:EDGE Certification Protocol, Section 2.3: Certification Levels; EDGE User Guide Version 2.1, Section 1.2: Scope of EDGE Certification.

Maintaining EDGE Auditor status involves specific requirements to ensure ongoing competence. The EDGE Expert and Auditor Protocols outline these requirements: “To maintain their status, EDGE Auditors must perform at least one project site audit every two years, attend refresher training as required by IFC, and stay updated by studying the EDGE user guides and protocols as they are revised” (EDGE Expert and Auditor Protocols, Section 5.1: Maintaining Auditor Status). Option A (performing at least one project site audit every two years) is explicitly required to demonstrate active engagement. Option B (studying the EDGE user guides as updated) is also necessary to stay current with program changes. Option D (attending refresher training) is mandated to ensure continued education. However, Option C (retaking the auditor exam) is not a requirement for maintaining status: “Once certified, EDGE Auditors are not required to retake the exam to maintain their status, though they may need to retake it if their certification lapses or if significant program changes occur” (EDGE Expert and Auditor Protocols, Section 5.2: Recertification Conditions). Since the question focuses on maintaining status, not recertification after lapse, retaking the exam is not a standard requirement. Thus, retaking the auditor exam (Option C) does not contribute to maintaining Auditor status.
Reference:EDGE Expert and Auditor Protocols, Section 5.1: Maintaining Auditor Status, Section 5.2:
Recertification Conditions.

An occupancy permit indicates that a building meets local regulatory requirements for occupancy,but it does not address the specific green building measures required for EDGE certification. The EDGE Certification Protocol clearly outlines the role of such permits in the audit process: “A local occupancy permit provided by the Client confirms that the building complies with local building codes and is ready for use. However, it does not replace the need to audit all EDGE measures, as EDGE certification requires verification of specific energy, water, and materials efficiency measures that are not typically covered by local permits” (EDGE Certification Protocol, Section 3.4: Post-Construction Requirements). Option A, does not replace the need to audit all EDGE measures, directly aligns with this guidance, as the Auditor must still verify each claimed measure (e.g., insulation, low-flow fixtures, fly ash concrete) against EDGE standards. Option B (replaces the need to audit all EDGE measures) is incorrect, as the permit does not address EDGE-specific requirements:
“Local permits do not verify EDGE measures like energy savings or embodied energy reductions, so a full audit is still required” (EDGE Expert and Auditor Protocols, Section 4.4: Site Audit Procedures). Option C (does not replace the need for desktop studies) is partially correct but less comprehensive, as desktop studies are only one part of the audit process: “Desktop studies are part of the audit, but the occupancy permit does not exempt any aspect of the EDGE audit, including site visits and measure verification” (EDGE Certification Protocol, Section 3.2: Audit Requirements). Option D (replaces the need to audit EDGE Materials measures) is also incorrect, as materials measures (e.g., use of fly ash concrete) require specific evidence like manufacturer’s data sheets, not covered by an occupancy permit: “Materials measures require detailed documentation of embodied energy reductions, which local permits do not address” (EDGE User Guide, Section 7.2: Materials Efficiency Measures). The EDGE User Guide further reinforces: “The Auditor must verify all EDGE measures through appropriate documentation and site visits, regardless of local permits, to ensure compliance with the EDGE standard” (EDGE User Guide, Section 6.3: Post-Construction Certification). Thus, the occupancy permit does not replace the need to audit all EDGE measures (Option A).
Reference:EDGE Certification Protocol, Section 3.4: Post-Construction Requirements, Section 3.2: Audit Requirements; EDGE Expert and Auditor Protocols, Section 4.4: Site Audit Procedures; EDGE User Guide Version 2.1, Section 6.3: Post-Construction Certification, Section 7.2: Materials Efficiency Measures.

Adoption of green building practices in EDGE is influenced by factors that incentivize or mandate resource efficiency. The EDGE User Guide discusses drivers for green building adoption: “Factors that lead to higher adoption of green building practices include green building regulations, which mandate compliance with efficiency standards; public awareness and capacity building, which educate stakeholders on the benefits of green design; and clear visibility of estimated savings and costs, which provide financial justification for green measures” (EDGE User Guide, Section 1.1: Introduction to EDGE). Option A (green building regulations) directly encourages adoption by enforcing standards: “Regulations requiring energy or water efficiency standards push developers to adopt green practices to meet legal requirements” (EDGE Certification Protocol, Section 1.2: Scope of EDGE Standard). Option C (public awareness and capacity building) increases adoption by educating stakeholders: “Awareness campaigns and training programs increase demand for greenbuildings by informing developers, owners, and tenants of their benefits” (EDGE User Guide, Section 1.1: Introduction to EDGE). Option D (clear visibility of estimated savings and costs) incentivizes adoption by demonstrating financial benefits: “EDGE’s display of savings and payback periods motivates adoption by showing the return on investment for green measures” (EDGE User Guide, Section 2.4:
Interpreting EDGE Results). However, Option B (lower electricity supply costs) may not lead to higher adoption, as it reduces the financial incentive to save energy: “Lower electricity supply costs decrease the cost savings from energy efficiency measures, potentially discouraging investment in green practices, as the payback period for measures like insulation or efficient lighting becomes longer” (EDGE Methodology Report Version 2.0, Section 4.4: Cost Savings Calculations). The EDGE User Guide further elaborates: “High utility costs often drive green building adoption by making energy and water savings more financially attractive, whereas lower costs can reduce the urgency to implement efficiency measures” (EDGE User Guide, Section 1.2: Scope of EDGE Certification). In this context, lower electricity supply costs (Option B) may not encourage green building practices, as the economic motivation for energy savings diminishes.
Reference:EDGE User Guide Version 2.1, Section 1.1: Introduction to EDGE, Section 1.2: Scope of EDGE Certification, Section 2.4: Interpreting EDGE Results; EDGE Certification Protocol, Section 1.2: Scope of EDGE Standard; EDGE Methodology Report Version 2.0, Section 4.4: Cost Savings Calculations.

The EDGE Auditor’s submission for Preliminary Certification (design stage) must include specific elements to support the recommendation for certification. The EDGE Certification Protocol specifies: “For Preliminary Certification, the EDGE Auditor’s submission must include compliance documents for the selected measures, such as drawings, specifications, and manufacturer’s data sheets, which verify that the design aligns with the self-assessment in the EDGE software. These documents are reviewed by the Certification Provider to confirm eligibility” (EDGE Certification Protocol, Section 3.2: Audit Requirements). Option C, compliance documents for selected measures, directly matches this requirement. Option A (all available design data) is too broad and not required: “Only documents directly related to the selected measures are needed, not all design data” (EDGE Certification Protocol, Section 3.2: Audit Requirements). Option B (Chapter 5 EDGE certification protocol) is incorrect, as this refers to the protocol document itself, not a submission component:
“The certification protocol is a reference, not part of the Auditor’s submission” (EDGE Certification Protocol, Section 1.1: Overview). Option D (design audit site visit results) is incorrect, as site visits are not required at the design stage: “Preliminary Certification is based on a desk audit, not a site visit, which occurs at the post- construction stage” (EDGE Certification Protocol, Section 3.3: Certification Decision). Thus, compliance documents (Option C) are required in the submission.
Reference:EDGE Certification Protocol, Section 3.2: Audit Requirements, Section 3.3: Certification Decision, Section 1.1: Overview.

The EDGE software’s Base Case is a standardized benchmark that does not adjust to project-specific corporate standards but reflects local norms. The EDGE User Guide states: “The Base Case in EDGE software is automatically generated based on local typical building practices and, where applicable, national building codes for the selected typology and location. It does not incorporate project-specific corporate standards or custom specifications, ensuring a consistent baseline for comparison” (EDGE User Guide, Section 2.3: Using the EDGE App). In this scenario, the hotel developer’s corporate design standards for water fittings, lighting, heating, and air-conditioning are specific to the project, but the EDGE Base Case will still use local typical practices or codes (Option C). Option A is incorrect, as the project can still be certified using the standard Base Case. Option B is wrong because the Base Case does not adapt to corporate specifications. Option D is also incorrect, as the Base Case is not verified on a case-by-case basis for specific hotel chains but is standardized for the region and typology.
Reference:EDGE User Guide Version 2.1, Section 2.3: Using the EDGE App; EDGE Methodology Report Version 2.0, Section 3.1: Base Case Determination.

The EDGE App relies on location-specific climate data to calculate resource savings, but not all cities are listed. The EDGE User Guide provides guidance for such cases: “If the project city is not listed in the EDGE App, the user should choose the closest city to the project location that is available in the database. If necessary, the user can edit the climate data (e.g., temperature, humidity) to better reflect the project’s actual conditions, ensuring accurate calculations” (EDGE User Guide, Section 2.2: Project Setup). Option B, choose the closest city and edit the climate data if necessary, directly matches this protocol. Option A (write to EDGE Certifier and wait) is incorrect, as this is not a required step: “Users are not required to request new cities; they can proceed by selecting the closest city” (EDGE User Guide, Section 2.2: Project Setup). Option C(select any city in the same climate zone globally) is too broad and inaccurate: “Choosing a city from a different region, even in the same climate zone, may lead to incorrect assumptions about local practices and climate” (EDGE Methodology Report Version 2.0, Section 3.2: Climate Data Inputs). Option D (choose the capital city) is also incorrect unless it is the closest: “The capital city should only be selected if it is the nearest available option in the database” (EDGE User Guide, Section 2.2: Project Setup). Thus, the correct protocol is to choose the closest city and edit climate data (Option B).
Reference:EDGE User Guide Version 2.1, Section 2.2: Project Setup; EDGE Methodology Report Version
2.0, Section 3.2: Climate Data Inputs.

Air-cooled chillers are a type of HVAC system commonly evaluated in EDGE for their energy efficiency in green building design. The EDGE Methodology Report Version 2.0 outlines the components of air-cooled chillers in the context of energy efficiency measures. According to the EDGE User Guide (Version 2.1), air- cooled chillers differ from water-cooled chillers by not requiring a cooling tower or associated water-based components like a condenser pump. The guide states: “Air-cooled chillers consist of a compressor, air-cooled condenser, thermal expansion valve, and evaporator, which work together to provide cooling by rejecting heat directly to the ambient air” (EDGE User Guide, Section 4.2: Energy Efficiency Measures). Option A includes a cooling tower and condenser pump, which are specific to water-cooled chillers. Option D mentions a water- cooled condenser, which is incorrect for air-cooled systems. Option C includes a chilled water pump, which is not a core component of the chiller itself but part of the broader system. Option B accurately lists the compressor, condenser (air-cooled, implied), thermal expansion valve, and evaporator, aligning with the EDGE description of air-cooled chiller components.
Reference:EDGE User Guide Version 2.1, Section 4.2: Energy Efficiency Measures; EDGE Methodology Report Version 2.0, HVAC Systems.

Increasing the glazing area in an office building affects various aspects of energy consumption due to changes in heat gain, heat loss, and natural light availability, but it does not influence all buildingsystems. The EDGE User Guide explains the impacts of glazing: “Increasing the glazing area (window-to-wall ratio, WWR) in an office building typically increases cooling demand due to higher solar heat gain, increases heating demand in colder climates due to greater heat loss through windows, and reduces lighting energy by allowing more natural daylight, assuming proper daylighting design” (EDGE User Guide, Section 3.5: Passive Design Strategies). Option A (cooling demand) is affected, as more glazing increases solar heat gain: “Higher WWR leads to greater cooling loads in hot climates due to increased solar radiation entering the building” (EDGE Methodology Report Version 2.0, Section 5.2: Energy Calculation Methods). Option B (heating demand) is also impacted, particularly in cooler climates: “Larger glazing areas increase heat loss in cold climates, raising heating demand due to the lower thermal resistance of windows compared to walls” (EDGE User Guide, Section 4.1: Insulation Measures). Option C (lighting energy) is affected, as more glazing can reduce the need for artificial lighting: “Increased glazing can lower lighting energy by enhancing daylight penetration, provided glare is controlled” (EDGE User Guide, Section 4.4: Lighting Efficiency Measures). However, Option D (hot water demand) is not impacted by glazing area, as hot water use is tied to occupant activities (e.
g., showers, cleaning) rather than building envelope design: “Hot water demand in EDGE is determined by occupant use patterns, such as the number of showers or laundry cycles, and is not influenced by glazing area or WWR” (EDGE Methodology Report Version 2.0, Section 4.2: Water Savings Calculations). The EDGE User Guide further confirms: “Glazing area impacts energy-related metrics like cooling, heating, and lighting, but has no direct effect on hot water demand, which is calculated separately based on usage assumptions” (EDGE User Guide, Section 5.2: Water Efficiency Measures). Therefore, increasing glazing area does not impact hot water demand (Option D).
Reference:EDGE User Guide Version 2.1, Section 3.5: Passive Design Strategies, Section 4.1: Insulation Measures, Section 4.4: Lighting Efficiency Measures, Section 5.2: Water Efficiency Measures; EDGE Methodology Report Version 2.0, Section 5.2: Energy Calculation Methods, Section 4.2: Water Savings Calculations.

EDGE Auditors must adhere to strict ethical guidelines to maintain independence and avoid conflicts of interest, particularly regarding payment structures that could influence their impartiality. The EDGE Expert and Auditor Protocols address payment terms explicitly: “An EDGE Auditor must confirm a fixed fee for their services that is independent of the final assessment result. Payment structures that tie fees to the success of certification, such as contingent payments, are prohibited to ensure the Auditor’s objectivity and to prevent any perception of bias in the audit process” (EDGE Expert and Auditor Protocols, Section 2.3: Conflict of Interest). The client’s offer of 50% payment for assessment and 50% upon successful certification violates this principle, as it makes part of the fee contingent on the outcome. Option A, confirm a fixed fee independent of the final assessment result, aligns with this ethical requirement, ensuring the Auditor’s impartiality. Option B (lodge a complaint with local authorities) is incorrect, as this is an overreaction and outside the Auditor’s role: “Issues related to payment terms should be resolved directly with the Client, not escalated to local authorities, which are unrelated to EDGE certification” (EDGE Expert and Auditor Protocols, Section 4.1: Audit Process). Option C (refer the developer to another Auditor) avoids the issue but does not address the ethical concern: “Referring the Client to another Auditor does not resolve the ethical violation of contingent fees, which applies to all Auditors” (EDGE Expert and Auditor Protocols, Section 2.3:
Conflict of Interest). Option D (accept the terms) is unethical, as it compromises the Auditor’s independence:
“Accepting payment terms tied to certification success, even if the project is likely to succeed, violates EDGE protocols and undermines the integrity of the certification process” (EDGE Certification Protocol, Section 3.1:
Certification Process). The EDGE User Guide further emphasizes: “Auditors must maintain strict independence, ensuring their compensation is not influenced by the certification outcome, to uphold the credibility of EDGE certification” (EDGE User Guide, Section 6.5: Working with EDGE Auditors). Thus, the Auditor should confirm a fixed fee (Option A).
Reference:EDGE Expert and Auditor Protocols, Section 2.3: Conflict of Interest, Section 4.1: Audit Process; EDGE Certification Protocol, Section 3.1: Certification Process; EDGE User Guide Version 2.1, Section 6.5:
Working with EDGE Auditors.

Insulation materials in EDGE are evaluated for their thermal performance and embodied energy as part of materials efficiency measures. The EDGE User Guide lists common insulation options: “In EDGE, insulation materials for walls, roofs, and floors include mineral wool, polyurethane,polystyrene, and fiberglass, which are selected for their low thermal conductivity and availability in most markets” (EDGE User Guide, Section
7.2: Materials Efficiency Measures). Options A (mineral wool), B (polyurethane), and D (polystyrene) are explicitly mentioned as insulation materials in EDGE. Option C, polypropylene, is not listed as an insulation material, as confirmed by the EDGE Methodology Report: “Polypropylene is a plastic material often used in packaging or pipes, but it is not recognized in EDGE as an insulation material due to its poor thermal resistance compared to standard insulation options like polystyrene or polyurethane” (EDGE Methodology Report Version 2.0, Section 6.1: Embodied Energy in Materials). The EDGE software’s material database further excludes polypropylene from insulation options, focusing instead on materials with established thermal properties for building envelopes. Thus, polypropylene (Option C) is not an insulation option in EDGE.
Reference:EDGE User Guide Version 2.1, Section 7.2: Materials Efficiency Measures; EDGE Methodology Report Version 2.0, Section 6.1: Embodied Energy in Materials.