2024年最新のに更新された検証済みの合格させるH12-811学習ガイドベスト問題集を使おう [Q87-Q108]

Rate this post

2024年最新のに更新された検証済みの合格させるH12-811学習ガイドベスト問題集を使おう Courses

究極なガイドはH12-811最新版限定公開

質問87、 What is the main function of the DHCP DISCOVER message?

The server’s confirmation response to the REQUEST message

The client is used to find the DHCP server

The client requests configuration confirmation, or renews the lease

The DHCP server is used to respond to the DHCP DISCOVER message, which carries various configuration information

質問88、 The wireless access controller (AC, Access Cntroller) is the unified management and control device in the FIT AP architecture. Which of the following description of the role of AC is wrong?

No matter when the data is forwarded, the user’s data message will be forwarded by AC

User access control

User access authentication

AP configuration delivery

質問89、 The OSI reference model from high-level to bottom-level is ().

Application layer, transport layer, network layer, data link layer, physical layer

Application layer, session layer, presentation layer, transport layer, network layer, data link layer, physical layer

Application layer, presentation layer, session layer, network layer, transport layer, data link layer, physical layer

Application layer, presentation layer, session layer, transport layer, network layer, data link layer, physical layer

質問90、 AC uses CAPWAP control tunnel to transmit management messages to FIT AP.

True

False

質問91、 Which parameter is used in the spanning tree protocol for root bridge election?

Port ID

Bridge priority

Root path cost

Bridge ID

質問92、 When AP and AC are on different Layer 3 networks, what method is recommended for AP to discover AC? (Multiple Choice)

Broadcasting method

DNS

DHCP

Manually specified on AP

質問93、 The configuration information of a certain port of the switch is shown in the figure, then this port carries VLAN TAG when sending data frames carrying which VLAN?
interface GigabitEtherneto/0/1
port hybrid tagged vlan 2 to 3 100
port hybrid untagged vlan 4 6
#

1,2.3,100

2.3.100

1,2.3.4.6,100

2.3.4.6,100

質問94、 Which of the following working modes are supported by Huawei Enterprise AP? (Multiple Choice)

Local

Cloud

FIT

FAT

質問95、 What is the protocol number corresponding to the ospf protocol at the network layer?

質問96、 Which of the following statements about IPv6 multicast addresses are correct? (Multiple Choice)

Provide redundant functions for services

Realize load sharing of services

The packet whose destination address is a multicast address will be sent to the nearest network interface in the sense of routing

Multicast addresses and unicast addresses use the same address space

質問97、 As shown in the figure below, the network and switch configuration information are shown in the figure. Which of the following statements is correct? (Multiple choice)

Data frames on the two links do not contain VLAN TAG

The PVID of the switch GigabitEthernet0/0/1 port is 20

Host A and Host B can be pinged

Host point and host B cannot ping

質問98、 In the CAPWAP tunnel establishment phase, after the AC receives the Join Request message sent by the AP, the AC will check the validity of the AP. Which of the following is the authentication method supported by the AC? (Multiple choice)

SN certification

Password authentication

MAC authentication

Not certified

質問99、 A device has been configured to complete the Telnet configuration. The device login address is 10.1.1.10. The Telnet user name is admin and the password is Huawei@123. Which of the following is the correct way to log in to this device using telnetlib?

telnetlib.Telnet （ 10.1.1.0,23,admin,Huawei@123 )

telnetlib.Telnet （ 10.1.1.0 )

telnetlib.Telnet （ 10.1.1.0,23, Huawei@123 )

telnetlib.Telnet （ 10.1.1.0,admin )

質問100、 FIT AP can work independently without relying on AC.

True

False

質問101、 The network shown in the figure below. The administrator hopes that RTA uses static routing, and preferentially sends data packets to RTB ‘s Loopback0 interface through G0/0/1 por, while G0/0/2 serves as a backup. So how to configure on RTA to achieve this requirement?

ip route-static 10.0.2.2 255.255.255.255 10.0.12.2 ip route-static 10.0.2.2 255.255.255.255 10.0.21.2 preference 40

ip route-static 10.0.2.2 255.255.255.255 10.0.12.2 preference 70 ip route-static 10.0.2.2 255.255.255.25510.0.21.2

ip route-static 10.0.2.2 255.255.255.255 10.0.12.2 ip route-static 10.0.2.2 255.255.255.255 10.0.21.2

ip route-static 10.0.2.2 255.255.255.255 10.0.12.2 ip route-static 10.0.2.2 255.255.255.255 10.0.21.2 preference 70

質問102、 Which of the following statement about static routing in Huawei equipment is wrong?

The cost value (Cost) of the static route cannot be modified.

The default value of the static route priority is 60

The range of the static route priority value is 1-255

When the priority of the static route is 0, the route will definitely be preferred.

質問103、 As shown in the figure, all four switches run STP, and various parameters adopt default values. If the G0/0/2 port of switch C is blocked and the configuration BPDU cannot be sent through this port, how long will it take for the blocked port in the network to enter the forwarding state?

about 3 seconds

about 50 seconds

about 30 seconds

about 15 seconds

質問104、 The network administrator configures the Huawei router RTA as shown in the figure. If a user needs to be authenticated in the authentication domain “huawei”, the correct description below is ().
[RTA]aaa
[RTA-aaa]domain Huawei
RTA-aaa-domain-huawei]authentication-s cheme aul
[RTA-aaa-domain-huawei]authentication-scheme au2

“authentication-scheme aul” authentication will be used, if “au1” is deleted, “au2” authentication will be used

Will use “au2” authentication and will use “authentication-scheme au1” authentication

Will use “authentication-scheme au2” authentication

“authentication-scheme au2” authentication will be used, if “au2” is registered, “aul” authentication will be used

質問105、 The Router ID of the OSPF process takes effect immediately after modification.

True

False

質問106、 As shown in the figure, there is a web server in the private network that needs to provide HITRP services to public network users. Therefore, the network administrator needs to configure NAT on the gateway router RTA to achieve the requirements. Which of the following configuration can meet the requirement?

RTA-Gigabitethernet0/0/1]nat server protocol tcp global 192.168.1.1 www inside 202.10.10.18080

[RTA-Seria11/0/1]nat server protocol tcp global 192.168.1.1 www inside 202.10.10.1 8080

[RTA-Gigabitethernet0/0/1]nat server protocol tcp global 202.10.10.1 www inside 192.168.1.18080

[RTA-Serial1/0/1]nat server protocol tcp global 202.10.10.1 www inside 192.168.1.1 8080

質問107、 As shown in the figure, a static NAT command is deployed on router R1. When the PC accesses the Internet, the destination address in the data packet will not change.

True

False

質問108、 Which of the following description about DD packets and LSA of OSPF is correct? (Multiple choice)

The header of an LSA can uniquely identify an LSA

LSA header is only a small part of LSA

DD packet contains detailed information about LSA

The DD packet contains only LSA header information

Loading …

HCIA-Datacom V1.0認定は、データ通信のキャリアを進歩させたいIT専門家にとって貴重な資産です。これは、データ通信技術と実践に関する個人の専門知識を実証するグローバルに認められた認定です。この認定は、個人が雇用市場で際立っていることを支援し、収益の可能性を高めることができます。

Huawei H12-811-ENU（HCIA-Datacom V1.0）認定試験は、専門家に多くの利点を提供する世界的に認められた認定です。認定試験は、データ通信技術のスキルと専門知識を認識する機会を提供します。認定試験は、新しい雇用機会、昇進、給与交渉を申請する際に追加の利点を提供します。この認定試験は、データ通信業界の次のレベルにキャリアを引き上げたい専門家にとって優れた投資です。

問題集で返金保証付きのH12-811承認済み問題集：https://www.passtest.jp/Huawei/H12-811-shiken.html