試験問題と解答は303学習ガイド問題を試そう！ [Q278-Q293]

質問 278
An HTTP monitor is created and assigned to a pool with the following non-default configuration:
Interval: 7 seconds
Timeout: 22 seconds
Reverse: Yes
Send String: GET/status.htmlHTTP/1.1/r/nHost:test.example.com/r/nConnector:Close Receive String: Up The HTTP server sends the following response:

What is the resulting pool status?

質問 279
A BIG-IP Administrator discovers malicious brute-force attempts to access the BIG-IP device on the management interface via SSH. The BIG-IP Administrator needs to restrict SSH access to the management interface.
Where should this be accomplished?

質問 280
A pool of four servers has been partially upgraded for two new servers with more memory and CPU capacity.
The BIG-IP Administrator must change the load balance method to consider more connections for the two new servers. Which load balancing method considers pool member CPU and memory load?

質問 281
What is the recommended procedure for upgrading a major TMOS release on a BIG-IP platform?

質問 282
Refer to the exhibit.

During a planned upgrade lo a BIG-IP HA pair running Active/Standby, an outage to application traffic is reported shortly after the Active unit is forced to Standby Reverting the flower resolves the outage. What should the BIG-IP Administrator modify to avoid an outage during the next for over event?

質問 283
— Exhibit –

— Exhibit —
Refer to the exhibit.
An LTM Specialist is troubleshooting an issue with a new virtual server. When connecting through the virtual server, clients receive the message “The connection was reset” in the browser. Connections directly to the pool member show the application is functioning correctly.
What is the issue?

質問 284
OneLTM device in an HA pair of LTM devices is unable to reach its default gateway. An HA Failover event needs to happen.
Which configuration item enables this behavior?

質問 285
A Standard Virtual Server for a web application is configured with Automap for the Source Address Translation option. The original source address of the client must be known by the backend servers. What should the BIG-IP Administrator configure to meet this requirement?

質問 286
An LTM Specialist needs to loadbalance an application using an LTM device to meet the requirements:
The application servers do NOT Support SSL, but client access to the application should be secured.
Multiple requests from the same client should be sent to the same pool member.
All pool members will have roughly the same processing power, and traffic should be distributed evenly.
The LTM device is NOT the pool members’ default gateway.
which configuration should the LTM Specialist.

質問 287
Which two items can be logged by the Application Visibility Reporting analytics profile? (Choose two.)

質問 288
A web server administrator informs the BIG-IP Administrator that web servers are overloaded Starting next month, the BIG-IP device will terminate SSL to reduce web server load. The BIG-IP device is ready using client SSL client profile and Rules on HTTP level. What actions should the BIG-IP Administrators to achieve the desired configuration?

質問 289
An LTM Specialist needs to create two virtual servers.
The application has links for both HTTP and HTTPS version of application. The client must be persistence to a pool member, no matter which virtual server isaccessed.
What must be selected in the Source Address Affinity persistence profile?

質問 290
An LTM Specialist needs to add a pool that will load balanceMYSOL services. It has four members, each with differing hardware platforms. All pool members are already assigned to another pool for load balancing FTP traffic.
Which load balancing method is most effective when the LTM Specialist sets up the pool?

質問 291
An LTM Specialist is troubleshooting virtual server 10.0.0.1:443 residing on VLAN vlan301. The web application is accessed via www.example.com. The LTM Specialist wants to save a packet capture with complete decrypted payload for external analysis.
Which command should the LTM Specialist execute on the LTM device command line interface?

質問 292
An LTM Specialist needs to apply SNAT using currently used SNAT pool to a new virtual server.
What needs to be completed before applying that configuration change?

質問 293
A custom HTTP monitor is failing to a pool member 10.10.3.75:8080 that serves up www.example.com.
A ping works to the pool member address.
The SEND string that the monitor is using is: GET/HTTP/l.l/r/n/Host.www.example.com/r/n/Connection Close/r/n/r/n Which CLI tool syntax will show that the web server returns the correct HTTP response?